|
|
|
Coaxial Video Ground Loop Isolator with B/I (TVS) Transient Voltage Suppressors for Surge Protection
We have now been able to lower the cost greatly and pass the savings on to you!
Specifications
- BNC male to BNC female with mini cable 15cm on both sides
- Passive, no power required
- Prevents video-signal distortion caused by video ground loops
- Eliminates picture tearing, cross talk and rolling
- Prevents power cables laid by others interfering with the CCTV system
- Built in Video BALUN, perfect to work with DVR to immunity DVR interference, for extra interference rejection
- Built in TVS (Transient Voltage Suppressors) for surge protection
- Click here for more CCTV Ground Loop Problem Solving tips
Got Ground Loop Problems?
The GBL01 Ground Loop Isolator is a passive device which can reduce Ground
Loop Interference with CCTV Video signals and can be easily installed in a new or
add to existing systems. It’s useful where a Video signal is transmitted via cable
between points with difference ground potentials. Differences in ground potential
are typically caused by unbalanced power line loads. It use to prevent video signal
distortion caused by video ground loops, eliminates picture tearing, humming bars,
cross talk and rolling, prevents power cables laid by others interfering with the
CCTV system. It built in TVS (Transient Voltage Suppressors) for surge protection, built in Video Balun, which perfect to work with DVR to immunity DVR interference, for extra interference rejection.
Where to Install the Ground Loop Isolator?
The Video Ground Loop Isolator should be installed at the CCTV Camera end by connecting the BNC Male connector of the Isolator to the camera and the BNC Male connector of the coaxial cable to the BNC Female connector on the Isolator. In a multi-camera installation it is recommended that a Video Ground Loop Isolator be installed for each camera.
What is Ground Loop?
A ground loop is an electrical problem that happens when an AC current interferes with the ground reference level of the video signal. It occurs on the conductive path formed by the shield of the video cable and the chassis of the video equipment.
A loop results from the difference between the voltage potential of the shield at one end of the cable, versus the voltage potential of the shield at the other end. The electrical level of the shield is usually 0 volts. When a ground loop is present, this level fluctuates above and below 0 volts. The greater the difference, the more severe the distortion or tearing. If the potential is too great it can destroy the equipment.
- What to look for:
- Slight distortion of the picture
- Hum bar or bars
Ground loops are an after-the-fact type of problem in which the end-user blames the installer, the installer blames the manufacturer, and actually nobody is at fault. Neither the manufacturer nor the installer can predict where a loop will occur. Only after the system is installed can it be determined if a problem will exist. Ground loop problems can be corrected. It is important for both the dealer and the end user to be aware that this problem can occur.
A ground loop problem may occur at several points in the system, and each occurrence of the problem must be corrected individually. Loops can occur between a camera and monitor, from a camera to a switcher or one of many other possibilities. Not all ground loops show up as picture disturbances. Erratic or strange behavior of other devices can be traced to grounding problems.
Remember, wires or connections labeled "common" or "neutral" are not mechanical ground connections even though they may be grounded within the equipment. Each should be treated as a separate wire and not allowed to touch ground or each other. Many people will resort to shortcuts and try to remove the earth ground (which is the middle prong on a 3-prong electrical plug) from the camera or the associated equipment.
Not only is this a very hazardous thing to do, it is also a violation of U.L. laws. When the earth ground is removed, a voltage can appear on the camera chassis. The camera will have what is called a "hot chassis" that can send 60 to 70 volts of electricity through anyone who touches it, which is enough to knock anyone off their feet.
|
| Order Information |
|
Item Number
GBL01
Price
$26.00
Quantity:
|
|
All Prices in US Dollars
|
 |
|
 |
 |
|
Single Channel H.264 IP Audio/Video Encoder w/ 4CIF, 2CIF, CIF or QCIF resolution settings, 30 frames per second
$775.00
NOVO Series 1 and 4 Channel Encoder , Built-In Web Server, 4xCIF, 2x4CIF, 30 fps / channel with Synchronized audio on every channel
$1,380.00
H.264 embedded DVR - 4, 8, 9, 16 ch, 4CIF, DCIF & QCIF, all units capable of 30 fps per channel with perfectly synchronized MP3 audio (***exception)
$1,758.00
HIGH-RES Hybrid Digital PC-Based Rack mount H.264 DVR/NVR, CIF-4CIF Res w/ Sync. Audio, 16 Internal RAID 5 Hard Drives and DVD-RW
$14,709.00
1/3", 1/2", and 1" CCD format Lens Selector / Viewfinder
$229.00
Super Shock Proof Armored High Speed 1/4" Sony EX-View PTZ - Day / Night, IP66 Weatherproof, IR up to 300 ft, , 3.4-122mm lens, NTSC/PAL - WDR option
$2,450.00
Hybrid Digital PC-Based Tower H.264 DVR/NVR Recorder, CIF-4CIF Res with Sync. Audio PLUS 16 IP Video Channels, License Included
$3,331.00
Coaxial Video Ground Loop Isolator with B/I (TVS) Transient Voltage Suppressors for Surge Protection
$26.00
Super Shock Proof Armored High Speed 1/4" Sony EX-View PTZ - Day / Night, IP66 Weatherproof, IR up to 262.5 ft, 3.4-122mm lens, NTSC/PAL - WDR option
$2,400.00
On SALE: $1,950.00
6" High Speed Day/Night Color High Speed PTZ, 36x optical 12x digital (420X zoom), Sony 1/4" EX-View HAD CCD, NTSC/PAL - WDR Option
$1,300.00
On SALE: $1,270.00
Ruggedized Mobile h.264 DVR - Real-Time Disp./Rec. up to 16 channels Audio / Video, 802.11g Wireless, live remote viewing, Wireless data transfer
$0.00
|
|
|
|